Engineering
15 versions in ten days, then one mechanism. This page holds the figures the product page leaves out. All forces and fall-out counts are simulated, not measured on a part.
Figures
Simulation with N35 magnets and nominal dimensions, status v6.9.
| Outer dimensions with caps | 84.75 × 40 × 20 mm |
|---|---|
| Tube | 40 × 20 × 2 mm, 80 mm face-ground |
| Button | 26.4 × 15.6 mm, flush, fins and grain texture, M logo |
| Clearance, drawer to tube | 0.25 mm per side, 0.30 mm to the top |
| Rest positions | 0 / 4.3 / 35.5 / 67.7 mm (closed / park / stage 1 / stage 2) |
| Holding force, closed | 1.22 N |
| Button actuation force | 1.75 N |
| Pull stage 1 to stage 2 | 2.42 N |
| Push stage 2 to stage 1 | 2.45 N |
| Remove from stage 2 | 2.45 N |
| Brake magnet | 1 per rail at 52 mm, reversed polarity |
| Magnets | 12 × NdFeB N35, Ø 4 × 2 mm, 10 in the rails, 2 in the drawer |
Brake bump
Opened steeply and with momentum, the drawer can run through all rest positions and fall out.
Since v6.9 each rail carries a fifth magnet at 52 mm, with reversed polarity. It repels the drawer magnet and brakes the drawer just behind stage 1. No new part is added, and the drawer still comes out.
Drawer falls out, of 72 cases
- no brake (v6.8)
- 50
- brake at 52 mm · production
- 1
- brake at 55 mm
- 5
- brake at 57 mm
- 7
- brake at 52 mm + 62 mm
- 1
Sensitivity to magnet strength
The N35 forces are the N52 model times 0.68. As a check, weaker and stronger magnets were calculated as well. “–” means not calculated.
| Factor | ×0.60 | ×0.68 | ×0.76 | ×0.85 |
|---|---|---|---|---|
| no brake | not calculated | 50 | 45 | not calculated |
| brake at 52 mm | 5 | 1 | 0 | 0 |
Practical test of v6.9: opened at an angle, the drawer stops in stage 1 or stage 2, even with momentum. Opened pointing straight down, it can slide out, as in the simulation.
Tolerances
3,000 units with randomly scattered dimensions, calculated with N52 magnets. The range covers 90 % of all units. With N35 the forces are about a third lower.
| Button actuation force | 2.1–2.7 N |
|---|---|
| Pull to stage 1 / 2 | 3.1–3.6 N |
| Holding force, closed | 1.6–2.1 N |
Assembly
Six printed parts, twelve magnets. No spring, no screw.
- Printed parts
- 06
- Magnets NdFeB N35
- 12
- Springs
- 00
Bill of materials
| Item | Part | Material | Production | Qty |
|---|---|---|---|---|
| 1 | Housing40 × 20 × 2 mm, 80 mm face-ground · E6/EV1 anodisedEN AW-6060 T6Precision cut | EN AW-6060 T6 | Precision cut | ×1 |
| 2 | Drawer with button2 lengthwise pockets · scoop radius · 45° slopes · fins, grain, M logo · 2 magnetsigus iglidur I150Additively manufactured, Baden-Württemberg | igus iglidur I150 | Additively manufactured, Baden-Württemberg | ×1 |
| 3 | Chassis with rear capEnd stop · button window 26.4 × 15.6 mm · crush ribsigus iglidur I150Additively manufactured, Baden-Württemberg | igus iglidur I150 | Additively manufactured, Baden-Württemberg | ×1 |
| 4 | Side rails L/ROn edge in the lower tube corners · 5 magnets each, 1 of them a brake magnetigus iglidur I150Additively manufactured, Baden-Württemberg | igus iglidur I150 | Additively manufactured, Baden-Württemberg | ×2 |
| 5 | Front capFlush · 0.15 mm gapigus iglidur I150Additively manufactured, Baden-Württemberg | igus iglidur I150 | Additively manufactured, Baden-Württemberg | ×1 |
| 6 | DividerSnaps in between the pockets without toolsigus iglidur I150Additively manufactured, Baden-Württemberg | igus iglidur I150 | Additively manufactured, Baden-Württemberg | ×1 |
| 7 | Neodymium magnets2 × 5 in the rails, 2 in the drawer · magnet on magnet · brake magnet reversed in polarityNdFeB N35, Ø 4 × 2 mmStandard part | NdFeB N35, Ø 4 × 2 mm | Standard part | ×12 |
Log
| Date | Entry | Value |
|---|---|---|
| Practical test of v6.9 passed: opened at an angle, the drawer no longer falls out, even with momentum. Only pointing straight down can it slide out.Test | Test | |
| Production specification fixed: all six inner parts in igus iglidur I150, NdFeB N35 magnets.I150 · N35 | I150 · N35 | |
| v6.9: one reversed-polarity brake magnet per rail at 52 mm. Simulation over 72 cases: opened steeply, the drawer falls out in 1 case instead of 50.12 magnets | 12 magnets | |
| v6.8: button with fins and grain texture like the print plate, M logo on the button.26.4 × 15.6 mm | 26.4 × 15.6 mm | |
| THUMB v6.3 released: button on the back, park position, 3,000 Monte Carlo simulations.4.3 mm park | 4.3 mm park | |
| Decision: THUMB becomes Model 01, ahead of DUO and CLICK.Score 4.35 | Score 4.35 | |
| Tube measured: narrower inside at the ends than in the middle. All moving parts designed for the tightest size.35.70–35.95 mm | 35.70–35.95 mm | |
| v1: three concepts, drawer, swivel pockets and flaps.3 concepts | 3 concepts | |
| Early development: drawing of drawer V3 in Fusion.Width 35.8 mm | Width 35.8 mm |
Next step: production of Batch 001.